Transmission tower parts and types of Transmission towers

For transmission of power at High voltage Transmission lines needed to be laid. For laying Transmission lines Transmission towers are most widely used in world. Transmission towers are used for following purposes:-
1.       To separate high voltage conductors from surroundings and from each other.
2.       To keep conductors at sufficient height for safe limits.


An overhead transmission line usually consists of three conductors or bundles of conductors containing the three phases of the power system. The conductors are usually aluminum cable steel reinforced (ACSR), which are steel core (for strength) and aluminum wires (having low resistance) wrapped around the core.

Tower designing is most important part as towers has to sustain natural calamities.  There are following parts in Transmission towers:-
1.       Tower top
2.       Cross arm
3.       Beam
4.       Insulator string
5.       Fork (K-Frame)/ Cage of Transmission tower
6.       Tower body & Leg of Transmission tower
7.       Tower base
8.       Vibration damper

Every part details will be discussed below:-
1.       Tower top:- Tower top is used to carry earth shield wire. This is connected at tip of tower also known as earth wire
2.       Cross arm:-
Cross arm is used to hold insulators. Insulators are used to carry transmission conductors. Dimensions of cross arm depends upon level of voltage to be transmitted.
3.       Beam:-
Beam is the portion between cross arms. This is used to hold cross arms.
4.       Insulator strings:-
Insulator string is used to carry transmission lines. There no. very depending upon the level of Transmission voltage to be transmitted. As the voltage level increase no. of insulators increases in a string.
5.   Cage of Transmission tower(Fork K-Frame):-
Cage is the main structure of Transmission towers which provides support to whole body of Transmission tower.
6.   Tower body and leg of Transmission tower:-
They are base of transmission tower. During design of Transmission tower minimum ground clearance of the lowest conductor point above the ground level is depends upon Tower body and leg of transmission tower. Higher the voltage to be transmitted higher will be the ground clearance required than higher will be the width between legs of Transmission towers.
7.   Tower base:-
Base of tower is the main holding of whole Transmission tower.
8.       Vibration Damper:-

As clear from its name these are used for damping out vibrations due to wind in transmission towers. If dampers are not used than conductors get fatigue from where it is hanged. There re 2 types of vibration dampers (i) VORTX/ Stock bridge Type (ii) Spiral vibration damper

Vortex/ Stock bridge type vibration dampers are most widely used.



Transmission tower height is crucial point for any Transmission tower design. Transmission towers height to be designed depending upon:-

(a)                Minimum ground clearance higher the level of voltage to be transmitted higher will be the ground clearance.  
(b)               Maximum sag of conductor. Sag is necessary evil in transmission lines, you can’t lay transmission conductors without sag.
(c)                Vertical gap between top and bottom conductors.
(d)               Gap between ground wire and top conductor.
A typical transmission tower with horizontal configuration height  is 100 feet.  These types of  towers  are designed to bear the vertical load of the conductor weight and horizontal loads from wind against the towers and the conductors.

There are following types of transmission towers:-
 a) Suspension/Tangent towers <2°
b) Small angle towers 2 ° -15 °
c) Medium angle towers 15 ° -30 °
d) Large Angle towers 30 ° -60 °
 e) Dead end towers >60 °
f) Transposition towers(4Xarms)
g) Special towers – JC, MC, NB, NBMC
h) Pole mounted termination towers
i) Mono poles



Comments

Post a Comment

Popular posts from this blog

A2XWY; A2XFY Cables meaning; XLPE cables advantages over PVC cables

Technical Specification of Aluminum Cables in terms of codes So many times you have seen coding while specifying cables technical such as A2XWY now what does this means. Now there is nomenclature for the same which is used while describing the same. Where A -  Aluminium 2X- XLPE Insulation W – Steel round wire armour F- Steel Strip Armour WW- Double Steel round Armour FF- Double Steel Strip Armour Y- PVC outer Sheath Wa- Non Magnetic round wire Armour Fa- Non Magnetic Strip Armour AW- Aluminum Wire Armour Now As per A2XWY – This describes that it is Aluminum cable, XLPE insulated, With Steel round wire armour and having PVC outer Sheath. This coding is as per IS 7098(Part1):1988. You have also seen that there is coding for copper so there is no coding required in case of copper cables. XLPE cables advantages over PVC cables/ Thermoplastic cables:- 1.       XLPE cables have higher Power rating about 1.2 times PVC cables 2.       XLP...
Read more

Digital Multimeter working principle; DMM working

Image
Digital multimeters are most widely used in every industry as it used for measurement of Voltage, Current, Resistance, Capacitance and various other parameters. DMMs have been available for very several years. Yet it is still challenging to locate advice about how a digital multimeter works. The operation of a digital multimeter is comparatively uncomplicated, although there are obviously differences in how digital mulimeters work if they're from different makers.Despite this, there are several similarities and some general principles of how digital multimeters work. Fundamentals of how a DMM functions The key process occurring within a digital multimeter for any measurement is that of voltage measurement. All other measurements are derived from this basic measurement. So the best technique for understanding how a digital multimeter functions is in understanding this procedure. There are many kinds to digital converter, ADC. Nonetheless the one that is most widely used DMMs in di...
Read more

Wireless voltmeter using Arduino and RF 433MHz receiver and transmitter

Image
In this project i showed you how to make a wireless voltmeter using arduino and RF 433MHz receiver and transmitter. You can use this code and concept for many other projects, any project which used sensor with analog voltage output to sense temperature, gas leakage or light , etc. For example you can put a LM35 temperature sensor rather than potantiometer, you just have to putting its formula which convert LM35 output pin voltage to exact temperature. You also can make a wireless AC or DC power meter by doing some change in code and hardware (using hall effect current sensor and single phase voltage sensor). This type of RF module has distance range up to 200 meters according to datasheet but when i bought this RF module from Aliexpress its distance rang was very low, but i set its adjustable RF coil very carefully and i get very higher distance rang.(Don't play with RF coil if your module works good), You also have to use a 6 inch antenna to increase distance range to max as possi...
Read more