ELCB working principle; Difference between ELCB and RCCB/RCD

Earth Leakage Circuit Breaker or ELCB

As clear from the name these circuit breakers are used for protection against electrical shock in case of leakage currents. ELCB get tripped whenever there are leakage currents in circuit. There are two types of ELCB’s:-

1.     Voltage ELCB
2.     Current ELCB

Now let’s discuss the same:-

1.   Earth leakage circuit breaker Voltage Type:-

As clear from the name these are voltage operated ELCB’s. These ELCB’s consists of relay coil. This relay coil is connected to the metallic body of equipment which is to be protected from earth leakage at one end and at other end it is connected to ground wire. If any fault occurs such as live wire touches the body than there will be voltage difference occur across the terminal of coil and earth. This voltage difference causes current to flow thus will operate relay and trips the ELCB. Voltage ELCB’s are available in various ranges these actuate as per limit described on ELCB’s.


Voltage ELCB’s are no longer used as there as following drawbacks:-

1.     These ELCB’s will disconnect the supply only incase there is fault between live and circuit earth. But these will not disconnect the supply if there are faults such as live part comes in contact with human body or live part comes in contact with water pipe etc. This happens because voltage across the circuit earth will not change.

2.     These ELCB’s not tripped even if there is fault between live and circuit breaker but there are parallel paths created other sources such as water pipes . As these cases ELCB get bypassed.

3.     These ELCB’s are used for protection of installation only but not the protection of human beings.

 

2.    Current ELCB’s:-

As clear from the name these ELCB’s operate on current leakages. These ELCB’s are most widely used in world. These ELCB’s are used for protection of both human beings and installations. These ELCB’s are used even when there is no earthing in installations. In general practice in electrical systems is that ELCB which are voltage based are known as ELCB’s and Current operated ELCB’s are known as RCD or RCCB. For principle and working of RCCB/ RCD please visit link as below:-

  

There is one advantage of ELCB’s over RCCB is that ELCB’s are less sensitive to fault current. In case of RCCB’s there will be some nuisance tripping.

Now days ELCB doesn’t exist in-fact RCCB is known as ELCB.

RCCB are used in House wiring also for protection of human beings from shock in case of any leakage currents.


 

Difference Between ELCB and RCCB:-

Even though ELCB doesn’t exist and now days RCCB is known as ELCB but in electrical systems there are following differences between ELCB and RCCB:-

1.     RCCB is current operated ELCB and ELCB is voltage operated ELCB.

2.     RCCB are used for protection for both Human beings and Circuit but ELCB is used for protection of Circuit only.

3.   RCCB used for detection of ay earth fault but ELCB are used for detection of earth faults which flows back through the main earth wire.

4.   RCCB has only line and neutral connections but in ELCB earth wire is connected through it.

 

RCCB ratings is usually in mA’s.

Human body can sustain electrical shock with magnitude of 30mA. RCCB in low voltage protection are designed such that they can trip off the circuit even for small currents upto 30mA. RCCB response time is usually in mSec’s. Thus RCCB will ensure protection of human body from electric shock.

Higher Range RCCB are also available in the market but these are used for protection where there is protection from fire hazard is sought. These are used where there is lot of flammable material is stored.

For houses RCCB range is Selected as 32-63A RCCB of 30-100 mA.

RCCB available in Market are 2 Pole and 4-pole.

2- Pole for Single Phase supply and 4-Pole of 3-Phase power supply.


 


Comments

Post a Comment

Popular posts from this blog

A2XWY; A2XFY Cables meaning; XLPE cables advantages over PVC cables

Technical Specification of Aluminum Cables in terms of codes So many times you have seen coding while specifying cables technical such as A2XWY now what does this means. Now there is nomenclature for the same which is used while describing the same. Where A -  Aluminium 2X- XLPE Insulation W – Steel round wire armour F- Steel Strip Armour WW- Double Steel round Armour FF- Double Steel Strip Armour Y- PVC outer Sheath Wa- Non Magnetic round wire Armour Fa- Non Magnetic Strip Armour AW- Aluminum Wire Armour Now As per A2XWY – This describes that it is Aluminum cable, XLPE insulated, With Steel round wire armour and having PVC outer Sheath. This coding is as per IS 7098(Part1):1988. You have also seen that there is coding for copper so there is no coding required in case of copper cables. XLPE cables advantages over PVC cables/ Thermoplastic cables:- 1.       XLPE cables have higher Power rating about 1.2 times PVC cables 2.       XLP...
Read more

Digital Multimeter working principle; DMM working

Image
Digital multimeters are most widely used in every industry as it used for measurement of Voltage, Current, Resistance, Capacitance and various other parameters. DMMs have been available for very several years. Yet it is still challenging to locate advice about how a digital multimeter works. The operation of a digital multimeter is comparatively uncomplicated, although there are obviously differences in how digital mulimeters work if they're from different makers.Despite this, there are several similarities and some general principles of how digital multimeters work. Fundamentals of how a DMM functions The key process occurring within a digital multimeter for any measurement is that of voltage measurement. All other measurements are derived from this basic measurement. So the best technique for understanding how a digital multimeter functions is in understanding this procedure. There are many kinds to digital converter, ADC. Nonetheless the one that is most widely used DMMs in di...
Read more

Wireless voltmeter using Arduino and RF 433MHz receiver and transmitter

Image
In this project i showed you how to make a wireless voltmeter using arduino and RF 433MHz receiver and transmitter. You can use this code and concept for many other projects, any project which used sensor with analog voltage output to sense temperature, gas leakage or light , etc. For example you can put a LM35 temperature sensor rather than potantiometer, you just have to putting its formula which convert LM35 output pin voltage to exact temperature. You also can make a wireless AC or DC power meter by doing some change in code and hardware (using hall effect current sensor and single phase voltage sensor). This type of RF module has distance range up to 200 meters according to datasheet but when i bought this RF module from Aliexpress its distance rang was very low, but i set its adjustable RF coil very carefully and i get very higher distance rang.(Don't play with RF coil if your module works good), You also have to use a 6 inch antenna to increase distance range to max as possi...
Read more