Configuration of ( HC-05 ) Bluetooth Module

   Yeah. Now we are going to discuss about the configuration of HC-05 Module using the Arduino board.


Hardware Required..

About Hardware...

  Arduino

          Arduino is an Open source Hardware come Software development kit which is used to develop and simulate your Innovative projects.

ARDUINO UNO

HC-05 Bluetooth Module

                 HC-05 embedded Bluetooth serial communication module has two work modes: order-response work mode and automatic connection work mode. And there are three work roles (Master, Slave and Loopback) at the automatic connection work mode. When the module is at the automatic connection work mode, it will follow the default way set lastly to transmit the data automatically.
When the module is at the order-response work mode, user can send the AT command to
the module to set the control parameters and sent control order.


HC-05


Working...

        Now make the circuit connection as shown in the Fig. Make sure your TXD and RXD is connected to the Default TXD and RXD of Arduino respectively.


Circuit Connection

   If your HC-05 have the RESET button. Do this..

               Do the circuit connections as shown. And don't plug your USB Cable. Press and Hold the RESET button and plug your USB cable. The two second blink indicates your module entered into AT Commands.

If your HC-05 did'nt have RESET button. Follow this..

           Do the circuit connection as shown. Expect the Vcc pin. Plug your USB cable and after then connect your Vcc pin to 3.3V. The two second blink shows you done good.

Programming...

          This is almost ZERO. No program is required to Configure yout HC-05 Module. Just open your Arduino IDE and upload it.
Program Window

     If you hit by any issue like Problem to uploading to board. Plug out The RXD and TXD. And Re upload the program and Plug in the RXD and TXD.

     Now. Its time to Configure. Open your Serial Monitor and make sure that the baud rate is selected of "38400" and "Both NL&CR" is selected. Type "AT" without quotes. If it responds OK. You done a good Job. If Any error message like ERROR(0) appears. Don't worry and Try Again.

Serial Monitor

   Now plug out and re plug in the USB cable. Without any connection with WAKE UP or EN pin. The continues blink show your Module is ready to pair with other devices.

Continues Blink



For more AT Commands click here

Watch the Video here.

Thank You for Your Time

Feel free to contact me @ abu786sagar@gmail.com

Comments

Post a Comment

Popular posts from this blog

A2XWY; A2XFY Cables meaning; XLPE cables advantages over PVC cables

Technical Specification of Aluminum Cables in terms of codes So many times you have seen coding while specifying cables technical such as A2XWY now what does this means. Now there is nomenclature for the same which is used while describing the same. Where A -  Aluminium 2X- XLPE Insulation W – Steel round wire armour F- Steel Strip Armour WW- Double Steel round Armour FF- Double Steel Strip Armour Y- PVC outer Sheath Wa- Non Magnetic round wire Armour Fa- Non Magnetic Strip Armour AW- Aluminum Wire Armour Now As per A2XWY – This describes that it is Aluminum cable, XLPE insulated, With Steel round wire armour and having PVC outer Sheath. This coding is as per IS 7098(Part1):1988. You have also seen that there is coding for copper so there is no coding required in case of copper cables. XLPE cables advantages over PVC cables/ Thermoplastic cables:- 1.       XLPE cables have higher Power rating about 1.2 times PVC cables 2.       XLP...
Read more

Digital Multimeter working principle; DMM working

Image
Digital multimeters are most widely used in every industry as it used for measurement of Voltage, Current, Resistance, Capacitance and various other parameters. DMMs have been available for very several years. Yet it is still challenging to locate advice about how a digital multimeter works. The operation of a digital multimeter is comparatively uncomplicated, although there are obviously differences in how digital mulimeters work if they're from different makers.Despite this, there are several similarities and some general principles of how digital multimeters work. Fundamentals of how a DMM functions The key process occurring within a digital multimeter for any measurement is that of voltage measurement. All other measurements are derived from this basic measurement. So the best technique for understanding how a digital multimeter functions is in understanding this procedure. There are many kinds to digital converter, ADC. Nonetheless the one that is most widely used DMMs in di...
Read more

Wireless voltmeter using Arduino and RF 433MHz receiver and transmitter

Image
In this project i showed you how to make a wireless voltmeter using arduino and RF 433MHz receiver and transmitter. You can use this code and concept for many other projects, any project which used sensor with analog voltage output to sense temperature, gas leakage or light , etc. For example you can put a LM35 temperature sensor rather than potantiometer, you just have to putting its formula which convert LM35 output pin voltage to exact temperature. You also can make a wireless AC or DC power meter by doing some change in code and hardware (using hall effect current sensor and single phase voltage sensor). This type of RF module has distance range up to 200 meters according to datasheet but when i bought this RF module from Aliexpress its distance rang was very low, but i set its adjustable RF coil very carefully and i get very higher distance rang.(Don't play with RF coil if your module works good), You also have to use a 6 inch antenna to increase distance range to max as possi...
Read more